Home

12V Electronic Automotive Car Auto Battery checker Relay Tester

12V Electronic Automotive Car Auto Battery checker Relay Tester

Description: AE100 is a quick go tester for relays that provides you with an indication of the general health and functioning of the most common Automotive relays. Tester will check for proper functioning of the relay contacts by connecting the car battery (11V--15V) to the relay coil. Tester will watch the pin configuration, the time to contacts closure and opening, consistency of the relay during each test session. Tester will light the GREEN LED if all passed during the test session, if not light the RED LED. Operating Instructions: 1. Connect the power leads to the car battery -- black alligator clip to negative terminal, red alligator clip to positive terminal. 2. Tester is powered up when the LED illuminates in RED. Check the relay before plugging into the tester. If it's a 4 pin relay, select '4 pin' on the tester. If it's a 5 pin relay, select '5 pin' on the tester. 3. Plug in the relay into one of the three receptacles. Press the 'Test' button. 4. Tester will check the pin configuration of the unknown relay. Tester will light the RED LED if the unknown relay is not the same to the most of common automotive relays or the pin of the unknown relay is destroyed. 5. Tester will open and close the relay 10 times for testing the time to contacts closure and opening if the pin configuration of the relay is right. Tester will light the RED LED immediately if the time is overtime. 6. Tester will check the consistency of the relay after testing the time to contacts closure and opening ten times. Tester will light the GREEN LED if the test passed, if not light the RED LED. 7. Disconnect power leads from the car battery and remove relay from the tester. Package Included: 1 X Automotive Relay Tester(JH100) 1 X User Manual 1 X Carry Bag

Auto/Boat/Plane/Accessories

12V Electronic Automotive Car Auto Battery checker Relay Tester

12V 2 Channel Relay Module With Optocoupler Support High Low Level Trigger For Arduino

12V 2 Channel Relay Module With Optocoupler Support High Low Level Trigger For Arduino

Features: 1. The module uses genuine quality relay, normally open interfaces maximum load: AC 250V/10A, DC 30V/10A 2. Using SMD OPTOCOUPLER isolation, driving ability, stable performance; trigger current 5mA 3. The module voltage is 5V/9V/12 V/24V are available 4. The module can be set to high or low triggered by jumper 5. Fault-tolerant design, even if the control line is broken, the relay will not operate 6. The power indicator (green) relay status indicator (red) 7. Interface design humane, all interfaces can be connected directly via terminal wiring leads very convenient 8. Module size : 50mm * 40mm * 16mm (L * W * H) 9. Has four mounting bolts holes, hole 3.1mm Interface: 1. DC+: Positive power supply (voltage required by the relay, there 5V/9V/12V/24V choice ) 2. DC-: Negative power connection 3. IN1: 1 channel signal to trigger the end, you can set a high or low level control relay 3. IN2: 2 channel signal to trigger the end, you can set a high or low level control relay Outputs: NO1: After a relay normally open interfaces relay before floating, shorted pull with COM1 COM1: 1 relay common interface NC1: 1 relay normally closed port, COM1 relay shorted before and after the pull- vacant NO2: 2 -way normally open relay interface, the relay before floating, pull back and COM2 short COM2: 2 Common Interface relay NC2: 2 channel normally closed relay interface relay short front and COM2, pull vacant post High and low trigger selection: S1 as a relay trigger selection of high and low S2 high and low for the two -way relay trigger selection Comes with low short circuit, triggering the corresponding relay is low, while the high end of the short com high trigger High and low trigger selection: Short jumper with LOW triggered when connected When the jumper is high with high short trigger Package includes: 1 x 12V 2 channel relay driver module for arduino

Electronics/Audio

12V 2 Channel Relay Module With Optocoupler Support High Low Level Trigger For Arduino

3Pcs 12V 2 Channel Relay Module With Optocoupler Support High Low Level Trigger For Arduino

3Pcs 12V 2 Channel Relay Module With Optocoupler Support High Low Level Trigger For Arduino

Features: 1. The module uses genuine quality relay, normally open interfaces maximum load: AC 250V/10A, DC 30V/10A 2. Using SMD OPTOCOUPLER isolation, driving ability, stable performance; trigger current 5mA 3. The module voltage is 5V/9V/12 V/24V are available 4. The module can be set to high or low triggered by jumper 5. Fault-tolerant design, even if the control line is broken, the relay will not operate 6. The power indicator (green) relay status indicator (red) 7. Interface design humane, all interfaces can be connected directly via terminal wiring leads very convenient 8. Module size : 50mm * 40mm * 16mm (L * W * H) 9. Has four mounting bolts holes, hole 3.1mm Interface: 1. DC+: Positive power supply (voltage required by the relay, there 5V/9V/12V/24V choice ) 2. DC-: Negative power connection 3. IN1: 1 channel signal to trigger the end, you can set a high or low level control relay 3. IN2: 2 channel signal to trigger the end, you can set a high or low level control relay Outputs: NO1: After a relay normally open interfaces relay before floating, shorted pull with COM1 COM1: 1 relay common interface NC1: 1 relay normally closed port, COM1 relay shorted before and after the pull- vacant NO2: 2 -way normally open relay interface, the relay before floating, pull back and COM2 short COM2: 2 Common Interface relay NC2: 2 channel normally closed relay interface relay short front and COM2, pull vacant post High and low trigger selection: S1 as a relay trigger selection of high and low S2 high and low for the two -way relay trigger selection Comes with low short circuit, triggering the corresponding relay is low, while the high end of the short com high trigger High and low trigger selection: Short jumper with LOW triggered when connected When the jumper is high with high short trigger Package includes: 3 x 12V 2 channel relay driver module for arduino

Electronics/Audio

3Pcs 12V 2 Channel Relay Module With Optocoupler Support High Low Level Trigger For Arduino

5Pcs 12V 2 Channel Relay Module With Optocoupler Support High Low Level Trigger For Arduino

5Pcs 12V 2 Channel Relay Module With Optocoupler Support High Low Level Trigger For Arduino

Features: 1. The module uses genuine quality relay, normally open interfaces maximum load: AC 250V/10A, DC 30V/10A 2. Using SMD OPTOCOUPLER isolation, driving ability, stable performance; trigger current 5mA 3. The module voltage is 5V/9V/12 V/24V are available 4. The module can be set to high or low triggered by jumper 5. Fault-tolerant design, even if the control line is broken, the relay will not operate 6. The power indicator (green) relay status indicator (red) 7. Interface design humane, all interfaces can be connected directly via terminal wiring leads very convenient 8. Module size : 50mm * 40mm * 16mm (L * W * H) 9. Has four mounting bolts holes, hole 3.1mm Interface: 1. DC+: Positive power supply (voltage required by the relay, there 5V/9V/12V/24V choice ) 2. DC-: Negative power connection 3. IN1: 1 channel signal to trigger the end, you can set a high or low level control relay 3. IN2: 2 channel signal to trigger the end, you can set a high or low level control relay Outputs: NO1: After a relay normally open interfaces relay before floating, shorted pull with COM1 COM1: 1 relay common interface NC1: 1 relay normally closed port, COM1 relay shorted before and after the pull- vacant NO2: 2 -way normally open relay interface, the relay before floating, pull back and COM2 short COM2: 2 Common Interface relay NC2: 2 channel normally closed relay interface relay short front and COM2, pull vacant post High and low trigger selection: S1 as a relay trigger selection of high and low S2 high and low for the two -way relay trigger selection Comes with low short circuit, triggering the corresponding relay is low, while the high end of the short com high trigger High and low trigger selection: Short jumper with LOW triggered when connected When the jumper is high with high short trigger Package includes: 5 x 12V 2 channel relay driver module for arduino

Electronics/Audio

5Pcs 12V 2 Channel Relay Module With Optocoupler Support High Low Level Trigger For Arduino

10Pcs 12V 2 Channel Relay Module With Optocoupler Support High Low Level Trigger For Arduino

10Pcs 12V 2 Channel Relay Module With Optocoupler Support High Low Level Trigger For Arduino

Features: 1. The module uses genuine quality relay, normally open interfaces maximum load: AC 250V/10A, DC 30V/10A 2. Using SMD OPTOCOUPLER isolation, driving ability, stable performance; trigger current 5mA 3. The module voltage is 5V/9V/12 V/24V are available 4. The module can be set to high or low triggered by jumper 5. Fault-tolerant design, even if the control line is broken, the relay will not operate 6. The power indicator (green) relay status indicator (red) 7. Interface design humane, all interfaces can be connected directly via terminal wiring leads very convenient 8. Module size : 50mm * 40mm * 16mm (L * W * H) 9. Has four mounting bolts holes, hole 3.1mm Interface: 1. DC+: Positive power supply (voltage required by the relay, there 5V/9V/12V/24V choice ) 2. DC-: Negative power connection 3. IN1: 1 channel signal to trigger the end, you can set a high or low level control relay 3. IN2: 2 channel signal to trigger the end, you can set a high or low level control relay Outputs: NO1: After a relay normally open interfaces relay before floating, shorted pull with COM1 COM1: 1 relay common interface NC1: 1 relay normally closed port, COM1 relay shorted before and after the pull- vacant NO2: 2 -way normally open relay interface, the relay before floating, pull back and COM2 short COM2: 2 Common Interface relay NC2: 2 channel normally closed relay interface relay short front and COM2, pull vacant post High and low trigger selection: S1 as a relay trigger selection of high and low S2 high and low for the two -way relay trigger selection Comes with low short circuit, triggering the corresponding relay is low, while the high end of the short com high trigger High and low trigger selection: Short jumper with LOW triggered when connected When the jumper is high with high short trigger Package includes: 10 x 12V 2 channel relay driver module for arduino

Electronics/Audio

10Pcs 12V 2 Channel Relay Module With Optocoupler Support High Low Level Trigger For Arduino

External Trigger Delay Switch Touch Button Relay Signal Timing Module Board

External Trigger Delay Switch Touch Button Relay Signal Timing Module Board

Feature: Model: YYC-2S 24 kinds of commonly used functions; can control the solenoid valve, water pump, motor, lights, etc. Input voltage: DC 5/6/12/24V optional Output power: can control the DC within 5A or AC load Time range: 0.01 seconds ~ 999 minutes adjustable at any time Terminal Description: 1. DC +: Input positive DC power supply 2. DC -: Input negative DC power supply 3. IN +: Signal input positive 4. IN -: Signal input negative 5. NO: Normally open relay interface, the relay hanging before pull-in, after pulled shorted connect to COM 6. COM: Relay Common Interface 7. NC: Normally closed relay interface, the relay is shorted connect to COM before pull-in, after pulled hanging Function list: P-11: Jog (offer signal to relay pull-in, the signal disappears, the relay stop) P-12: Self-locking (offer signal to pull, give a signal again to stop relay) P-13: Offer signal, the relay will stop automatically for A second; trigger will be invalid during the delay time P-14: Offer signal, the relay will stop automatically for A second; trigger re-timing during the delay time P-15: Offer signal, the relay will stop automatically for A second; trigger superimposed during the delay time P-16: Offer signal, the relay will stop automatically for A second; trigger reset during the delay time P-17: Offer signal, relay pull-in, input signal is disconnected, start counting time after A second power off, during the delay period offer signal again to keep output, timing stop P-18: When power is on, the relay will pull in immediately and power will be off after A second delay; until the next power-on P-21: Offer signal, delay A seconds, the relay pull P-22: Offer signal, more than A seconds, the relay pull, the signal disappears, the relay stops P-23: After the signal disappears for more than A second, the relay will be closed, the signal will disappear and the relay will stop P-24: When the signal exceeds A second, the relay will be closed and the relay will stop after the signal disappears for more than A seconds P-25: When t

Electronics/Audio

External Trigger Delay Switch Touch Button Relay Signal Timing Module Board

DC12V 4-Channel Android Mobile Bluetooth Relay Module

DC12V 4-Channel Android Mobile Bluetooth Relay Module

Overview: LC 12V Bluetooth 4-channel relay module equip with SPP-C Bluetooth 2.1 slave module and 8 bit high performance MCU, you can control the relay with cellphone APP directly. APP LCBS download separately (recommended): http://files.banggood.com/2018/08/LC-BLUETOOTH-SWITCH(LCBS).apk>>>>>>Click here Use data download package (included app): http://files.banggood.com/2018/08/LC-WM-Relay.zip>>>>>>Click here Bluespp Bluetooth serial APP separately download: http://files.banggood.com/2018/08/bluespp_6.4.apk>>>>>>Click here The function and characteristics: 1, On-board N76E003/STM8S003 and SPP-C Bluetooth 2.1 module 2, The relay can be controlled with APP 3, Effective control distance(on open area): 10m 4, Power supply: 12V 5, On-board 12V, 10 A / 250 v AC 10 A / 30 v DC relay, absorb 100000 times continuously, Module with diode effusion protection, short response time 6, On-board optocoupler isolation components, anti-interference ability is strongly 7, On-board Bluetooth indicator and relay indicator LED 8, On-board preserved UART debug interface(Baud rate is 9600) and MCU program interface 9, Size: 62.7*63.2mm Interface: IN+ IN-: 12V power input TX, RX: UART communication SWIM, NRST: MCU program interface LED D2/D3/D4/D5(red): Relay indicator LED D1(blue): Bluetooth state indicator, the description of D1 as below: (1)It's means wait for establishing connection with the APP when D1 blink slowly (2)It's means the Bluetooth connect with the APP successfully when D1 on all the time Relay control command(must be hex format): Open the 1st relay: A0 01 01 A2 Close the 1st relay: A0 01 00 A1 Open the 2nd relay: A0 02 01 A3 Close the 2nd relay: A0 02 00 A2 Open the 3rd relay: A0 03 01 A4 Close the 3rd relay: A0 03 00 A3 Open the 4th relay: A0 04 01 A5 Close the 4th relay: A0 04 00 A4 Package included: 1 x DC12V 4-Channel Bluetooth Relay Module

Electronics/Audio

DC12V 4-Channel Android Mobile Bluetooth Relay Module

Easy Checker Immobiliser System Fast Tester for Mercedes Benz BMW Audi VW

Easy Checker Immobiliser System Fast Tester for Mercedes Benz BMW Audi VW

Easy Checker Immobiliser System Fast Tester for Mercedes-Benz BMW Audi VW Support car model: Support for all models for Mercedes-Benz 1998-2010; support all models for BMW 1995-2010; support for Audi / VW new smart key. How to use Easy-Checker? for Benz car model: Put Easy-Chcker on the EIS, put your IR key into EIS. Light on and not off, then EIS and key all ok Light on then off, then EIS ok,key not ok Light on and not off but car still can not start, please check ESL Steering wheel lock and Key whether ok. Light not on,then EIS not ok. for BMW Car model: EWS system: Put Easy-Checker on EWS(no need insert key) Light on means EWS ok(can used on:E46/E39/E53) Insert Easy-Checker into EWS(insert key in) Light on not off,then Key and EWS all ok Light on then off, then EWS ok, key not ok Light on and not off,but car still not start, please check whether key is ok CAS System( for 1 series/3 series/ 5 series/7 series) Put Easy-Checker directly on CAS and insert key in Light on and not off, then CAS and key all ok Liht on then off, then CAS OK but key not ok for AUDI /VW Car model: Smart Key slot-key Put Easy-Checker directly on the EZS and insert key in Light on and not off, then EZS and key ok Light on then off, then EZS ok,key not ok Package including: 1 X Easy-Checker

Auto/Boat/Plane/Accessories

Easy Checker Immobiliser System Fast Tester for Mercedes Benz BMW Audi VW

DC5V 4-Channel Android Mobile Bluetooth Relay Module

DC5V 4-Channel Android Mobile Bluetooth Relay Module

Overview: 5V Bluetooth 4-channel relay module equip with SPP-C Bluetooth 2.1 slave module and 8 bit high performance MCU, you can control the relay with cellphone APP directly. APP LCBS download separately (recommended): https://pan.baidu.com/s/1dFNa2kx Use data download package (included app): https://pan.baidu.com/s/1bprWzO7 Bluespp Bluetooth serial APP separately download: https://pan.baidu.com/s/1dEYlIqX The function and characteristics: 1, On-board N76E003/STM8S003 and SPP-C Bluetooth 2.1 module 2, The relay can be controlled with APP 3, Effective control distance(on open area): 10m 4, Power supply: 5V 5, On-board 5V, 10 A / 250 v AC 10 A / 30 v DC relay, absorb 100000 times continuously, Module with diode effusion protection, short response time 6, On-board optocoupler isolation components, anti-interference ability is strongly 7, On-board Bluetooth indicator and relay indicator LED 8, On-board preserved UART debug interface(Baud rate is 9600) and MCU program interface 9, Size: 62.7*63.2mm Interface: IN+ IN-: 5V power input TX, RX: UART communication SWIM, NRST: MCU program interface LED D2/D3/D4/D5(red): Relay indicator LED D1(blue): Bluetooth state indicator, the description of D1 as below: (1)It's means wait for establishing connection with the APP when D1 blink slowly (2)It's means the Bluetooth connect with the APP successfully when D1 on all the time Relay control command(must be hex format): Open the 1st relay: A0 01 01 A2 Close the 1st relay: A0 01 00 A1 Open the 2nd relay: A0 02 01 A3 Close the 2nd relay: A0 02 00 A2 Open the 3rd relay: A0 03 01 A4 Close the 3rd relay: A0 03 00 A3 Open the 4th relay: A0 04 01 A5 Close the 4th relay: A0 04 00 A4 Control the relay with APP: 1, The IN+ IN- connect to 5V DC adapter 2, Controlled the relay with APP There are 2 types APP available: one is a specialized APP that designed by LCTECH, another one is a common APP that downloaded from Android market. 2.1, Specialized APP instructions: 2.1.1, Install the 'BluetoothDemo' APP on your Android phone, open it and cl

Electronics/Audio

DC5V 4-Channel Android Mobile Bluetooth Relay Module

DC 12V Bluetooth Relay Board Mobile Phone Bluetooth Remote Control Switch

DC 12V Bluetooth Relay Board Mobile Phone Bluetooth Remote Control Switch

Summarize: DC 12V bluetooth relay board include single channel 12V/10A relay module and SPP-C bluetooth serial port slave module, Can be sent via mobile phone APP commands to control the relay switch. APP LCBS download separately (recommended): http://files.banggood.com/2018/08/LC-BLUETOOTH-SWITCH(LCBS).apk Use data download package (included app): http://files.banggood.com/2018/08/LC-WM-Relay.zip Bluespp Bluetooth serial APP separately download: http://files.banggood.com/2018/08/bluespp_6.4.apk Functional features: (1) Onboard SPP - C bluetooth serial port slave module, with wireless control function. (2) Onboard 12 v,10 A / 250 V AC 10 A / 30 V DC relay, relay long life can absorb 100000 times in a row. (3) Module with diode effusion protection, short response time. (4) Onboard bluetooth status indicator light (when not connected flash, slow connection after long bright) and relay status indicator light . (5) Control distance 10m (open environment) Technical parameters: Follow the bluetooth 2.1 + EDR specification Module working voltage VCC: DC 12 v DC control maximum voltage: DC 30 v Exchange control maximum voltage: AC 250 v Size: 20mm*62mm Basic function and instructions: IN + : DC 12 v power supply to the anode IN -: DC 12 v power supply COM: public side NO: relay normally open interface, relay and impending, before and after absorption and COM sub.NC: relay normally closed interface, relay and with COM nipple, before and after the impending. Basic instructions: After wiring correct, using cellphone to search Bluetooth devices and connect, Pairing password is 1234, Input order and send by hexadecimal (when the Input order is A00101A2 open the relay when the Input order is A00100A1 close the relay) Note: When Wiring NO NC COM:Can't access to any two port ,or will be short circuit. Package included: 1 x DC 12V Bluetooth Relay Board

Electronics/Audio

DC 12V Bluetooth Relay Board Mobile Phone Bluetooth Remote Control Switch

Ethernet Control Module With 16 CHs Relay For Arduino LAN WAN WEB Server RJ45 Android iOS

Ethernet Control Module With 16 CHs Relay For Arduino LAN WAN WEB Server RJ45 Android iOS

Overview: This is an Ethernet Controller board based on Imatic system which could be compatible with the 16 Channels relay. Using the controller module and the 16 Channels relay, you could control up to 16 devices remotely on LAN or WAN. The Ethernet Controller board has integrated the web server, when you are on your office, you just need to open the page on your computer, pad or smartphone, and then control your devices like lights, air-conditioning or refrigerator on your home. You can feel free to enjoy the remote controlling of your other devices with the ethernet controller board. Feature: Control switches remotely together with 16 Channel relay. RJ45 interface, via RJ45 telecommunications connection for network control. Support for 16 Channels relay which means you could controll more to 16 different devices at the same time. Unique dual TCP connect control, corresponding with above trait, local as TCP server accept client control, when connect to remote server as TCP client Supply core module detailed information Default IP: 192.168.1.4 prot:30000 http://192.168.1.4/30000 (You could change the default IP address) Relay: 175 * 90 * 20mm Relay + controller: 215 * 90 * 25mm HTTP comment: http://192.168.1.4/30000/00 : Relay-01 OFF http://192.168.1.4/30000/01 : Relay-01 ON http://192.168.1.4/30000/02 : Relay-02 OFF http://192.168.1.4/30000/03 : Relay-02 ON http://192.168.1.4/30000/04 : Relay-03 OFF http://192.168.1.4/30000/05 : Relay-03 ON http://192.168.1.4/30000/30 : Relay-16 OFF http://192.168.1.4/30000/31 : Relay-16 ON http://192.168.1.4/30000/41 : Enter http://192.168.1.4/30000/40 : Exit http://192.168.1.4/30000/42 : Next Page http://192.168.1.4/30000/43 : Next Page Package includes: 1 x Ethernet Control Module 1 x 16 channel relay Wiring, for reference only.

Electronics/Audio

Ethernet Control Module With 16 CHs Relay For Arduino LAN WAN WEB Server RJ45 Android iOS

12V 120W Portable Car Wireless Wet and Dry Dual Use Household Vaccum Cleaner

12V 120W Portable Car Wireless Wet and Dry Dual Use Household Vaccum Cleaner

Feature: Type: Vaccum cleaner for portable vehicles Rated speed: 22800 (r / min) Vacuum suction: 40 (mbar) Rated input power: 120 (W) Can absorb coins, confetti, water, ash 120W power provides continuous stable power, fast heat dissipation, less than 50dB, strong power and quiet 360 cyclone integrated warehouse HEPA filter can be washed Package Included: 1 X Car Home Vaccum Cleaner

Auto/Boat/Plane/Motorcycles

12V 120W Portable Car Wireless Wet and Dry Dual Use Household Vaccum Cleaner

Inflatable Boat Kayak Air Pump Hose Adapter H-R Valve Adapter

Inflatable Boat Kayak Air Pump Hose Adapter H-R Valve Adapter

Inflatable Boat Kayak Air Pump Hose Adapter H-R Valve Adapter Feature: - High flexibility, high strength, environmental protection - Consistent with the original product size, long life use - Easy to use Specification: Color: Black Material: PVC Size: 30x55mm Suitable For: Various kayaking Package Included: 1 X Valve Adapter

Auto/Boat/Plane/Parts

Inflatable Boat Kayak Air Pump Hose Adapter H-R Valve Adapter

Hood 4549L-R Lift Car Supports Shock Gas Cylinder Pair Kit Set Fits For Toyota Avalon

Hood 4549L-R Lift Car Supports Shock Gas Cylinder Pair Kit Set Fits For Toyota Avalon

Description: 1. Easy to install with simple hand tools in just minutes. 2. Engineered and built to meet or exceed OE. quality standards. 3. Patented multi lobe seal offers leak free operation and long life. 4. Exact fit original equipment design guarantees correct fit and function. 5. Self clean piston assembly delivers smooth operation and consistent performance. 6. Hardened, Chrome Plated Steel Piston Rod; Rubber O-ring piston seal for controlled lift. 7. Heavy gauge steel pressure tube provides long life; Teflon backup ring gives enhanced performance. Feature: Extended Length: 45cm Color: Black Fitment: For Toyota Avalon Base Sedan 1995-1999 4-Door Hood (L-R) For Toyota Avalon XL Sedan 1995-1999 4-Door Hood (L-R) For Toyota Avalon XLS Sedan 1995-1999 4-Door Hood (L-R) Package Included: 2 X Lift Supports 8 X Accessories

Auto/Boat/Plane/Repair

Hood 4549L-R Lift Car Supports Shock Gas Cylinder Pair Kit Set Fits For Toyota Avalon

3 Buttons Silicone Remote Key Case Holder For Accord Crosstour For 2015-2017

3 Buttons Silicone Remote Key Case Holder For Accord Crosstour For 2015-2017

Description: 1. Eco friendly silicone,odorless and non-toxic. 2. Silicone shell only.No remote or electronic internals. 3. Working life at least up to 10 years unless it is man-made damage. 4. This cover can withstand high temperature and not easy to distort or fade. 5. This cover can protect you car remote from scratching/dropping and for anti-vibration. Feature: Model Number: 588022 Product Name: Key Cover Condition: 100% Brand New Material: Silicone Color: white / green / pink / blue / dark blue / black / red Size : 68.5mm/2.7in x 40mm/1.57in x 16.5mm/0.65in (L x W x H) Quantity: 1 Fitment: For Honda Accord Crosstour 2015-2017 Package Included: 1 X Silicone Key Cover

Auto/Boat/Plane/Accessories

3 Buttons Silicone Remote Key Case Holder For Accord Crosstour For 2015-2017

Drive Shaft Coupling Rubber Mount Bushing For BMW

Drive Shaft Coupling Rubber Mount Bushing For BMW

Description: 1. Top-grade materials 2. High-precision manufacturing tools 3. State-of-the-art production techniques 4. Utilizing high precision and latest technology comes the OEM quality drive shaft flex joints. Feature: Type: Constant Speed Drive Shaft Application / Position: 110mm Diameter Height: 32 mm Inside Diameter: 38 mm Outside Diameter: 110 mm Distance Betweeen Hole: 78 mm Mnumber Of Holes: 6 Manufacturer Part Number: 26111227410 Applicable Models: F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 Package Included: 1 X Drive Shaft Coupling

Auto/Boat/Plane/Repair

Drive Shaft Coupling Rubber Mount Bushing For BMW

52mm 2 Inch Universal Car Smoke Lens LED Pointer Water Oil Temperature Temp Gauge Meter

52mm 2 Inch Universal Car Smoke Lens LED Pointer Water Oil Temperature Temp Gauge Meter

Description: 1. Racing look enhance the characteristic to your car. 2. Oil Temperature Gauge monitor engine oil temperature, ensuring motor oil does not break down causing harmful wear and tear to your engine. 3. Comes with installation manual. Feature: Model number: A31370 Product name: oil temperature gauge Material: Metal Voltage: 12V Reading range: 100-300 degrees fahrenheit Housing color: White Lens color: Smoke-tinted Pointer color: Red Diameter: 57mm/2.24 inch The distance of two bolt: 39.7mm/1.56 inch Fitment: Universal Car 2 inch/52mm diameter oil temperature gauge Package Included: 1 X Oil Temperature Gauge 1 X Sensor 1 X Manual

Auto/Boat/Plane/Accessories

52mm 2 Inch Universal Car Smoke Lens LED Pointer Water Oil Temperature Temp Gauge Meter

4Pcs Door Lock Ring Protective Car Cover Case For Honda Accord Civic CR-V

4Pcs Door Lock Ring Protective Car Cover Case For Honda Accord Civic CR-V

Description: 1. Material: high quality PP Plastic. 2. Compact, practical and beautiful. 3. Enhancing your car's overall temperament 4. Waterproof and Rustproof. Make your car clean and safe. 5. Easy installation, do not need to remove any parts and any screw. 6. Injection-molded thermoplastic provides superior strength and durability. Feature: Model Number: 527006 Product Name: Protective Cover Material: PP Plastic Color: Black Size: 6.9x5.3cm Quantity: 1Set Fitment: For Honda Accord 2008+ For Honda Civic 2005+ For Honda CR-V 2007+ For Honda Fit 2008+ Package Included: 4 X Door Striker Cover Lock Protector 4 X Door Check Arm Protection Cover

Auto/Boat/Plane/Repair

4Pcs Door Lock Ring Protective Car Cover Case For Honda Accord Civic CR-V

Anderson 30A Power Supply Connector Plug For Golf Trolley

Anderson 30A Power Supply Connector Plug For Golf Trolley

Description: 1. Silver plated Copper terminals. 2. Light and durable polycarbonate housing. 3. 10 X 30 AMP ELECTRICAL CONNECTOR PLUG, GOLF TROLLEY, KIT CAR 4. Can be used on a wide range of applications needing a high quality, secure connection. 5. They are genderless (no male or female) simply turn one 180 degrees to fit into the other. 6. Used extensively on golf trolley charging circuits, kit car builds, amateur radio, remote control items etc. 7. These plugs can be locked together into any block shape and size to create the perfect multi-pole connector for your needs. Feature: Material: Plastic& Aluminum Current: 30 amps Voltage: 600 Volts (Max) Approx Dimensions: 7.9mm 7.9mm 24.6mm Package Included: 10 X nterlocking plugs 10 X Terminals

Auto/Boat/Plane/Repair

Anderson 30A Power Supply Connector Plug For Golf Trolley

12V 6700K 300LM LED DRL Daytime Running Light Turn Singal Lamps for Ford Escape Kuga 2013-2016

12V 6700K 300LM LED DRL Daytime Running Light Turn Singal Lamps for Ford Escape Kuga 2013-2016

Specification: Material ABS Housing+High-brightness LED Light Color White(Daytime Running Light) +Yellow (Turn Singal Light) Color Temperature 6000K~6700K Placement on Vehicle Front ,Left,Right Brightness 200lm~300lm Voltage 12V Size 36.5x4x3 cm Fitment For Ford Escape Kuga 2013-2016 Wire Connection: Black Wier--Negative Pole Red Wire--ACC+ White Wire--Trun Signal Blue Wire--Headlight Note: 1.We provide clear pictures, measurements where possible. Please check as much as possible to make sure the item is the one that you need. 2.Please allow 0.5-1cm difference due to manual measurement. 3.Installation instructions is not included. Professional installation is highly recommended. 4.The color of the actual items may slightly different from the listing images due to different computer screen, thanks for your understanding. Package Included: 2 X Daytime Running Light 1 X DRL Digital Controller

Auto/Boat/Plane/Car Audio

12V 6700K 300LM LED DRL Daytime Running Light Turn Singal Lamps for Ford Escape Kuga 2013-2016

210cm*38cm Sports Stripe Pattern Style Car Stickers Vinyl Decal for Race SUV Side Body

210cm*38cm Sports Stripe Pattern Style Car Stickers Vinyl Decal for Race SUV Side Body

Specification: Material PVC Color Black, White, Red, Yellow, Blue Size 210cm / 82.68' x 38cm / 14.96' Placement on Vehicle Side Type Decal Surface Finish Glossy Fitment Universal Features: 1. High temperature resistant, surface antifouling UV coating. 2. Glossy, texture like car paint. 3. Waterproof sunscreen, no fading. 4.Tear off without leaving the residue, do not hurt the paint. Tips: Just peel off the backing, apply decal to smooth, clean surface, press firmly on decal, then remove transfer tape. Decals are not printed, they are cut out of vinyl. There is no background on these decals. The colored portion is the only part that is a decal. (Please note tools are not included.) Note: 1.We provide clear pictures, measurements where possible. Please check as much as possible to make sure the item is the one that you need. 2. Please allow 0.5-1cm difference due to manual measurement. 3.There are no instructions included in this kit.If you want to know how to use or install it, please contact us by Email.We will provide help as much as possible. Package Included: 2 X Car Stickers

Auto/Boat/Plane/Parts

210cm*38cm Sports Stripe Pattern Style Car Stickers Vinyl Decal for Race SUV Side Body